Windshield Repair Kit and Headlight Restoration Kit for Car Lamp Plastic Lens Restore Renew Polish Repair Hand Tool Sets
Headlamp restoration kit contains:
2x P800 Sanding Discs
2x P1200 Sanding Discs
2x P2000 Sanding Discs
1x Sponge Disc
2x 40gm Polish Paste
2x 3.0ml Protect Liquid
1x Mask Tape (300x2cm)
1x Backer Pad M10 Thread
1x Adaptor
1x Sponge Disc White
Headlights restoration kit:
Product descriptions:
Plastic lens can yellow with age, reducing headlight brightness, and new lenses can be expensive. The headlight restoration kit lets you shine and restore plastic lens, including headlights, tail lights, fog and directional lights. By restoring clarity to the lens, the performance of the headlight is improved and the appearance of the vehicle is enhanced. Now you can produce professional results with the headlight restoration kit. Kit includes all items necessary to perform the task.
Features and Advantages:
Helps restore clear plastic by removing haze and discoloration.
Provides a deep clean to yellowed, hazed headlights with the use of a specially designed polish and sealant.
Improves visibility and safety.
One kit is intended to restore two headlight lenses.
This inexpensive kit saves hundreds of dollars and restores crucial night time visibility by restoring your own lenses.
Easy, 5-step process requires as little as an hour to remove scratches and restore cloudy, dull lenses.
Application:
Process:
Mask
Protect trim and painted surfaces around the headlight lens with masking tape.
Clean & lubricant
Using the spray bottle (STEP 1), apply enough lubricant to the lens surface before sanding.
Sand (about 2-3 minutes)
Wear attached gloves, Using three grits (P400,P800,P1000) sanding disc orderly to sand away the yellowing and surface defects from lens. Replace with a new sanding disc if need and continue sanding until the yellow layer completely removed. Spray lubricant to the surface if it becomes dry while sanding.
Refine
Dispense some polishing paste (STEP 2) onto the cleaning cloth to polish out the remaining scratches. When the cloth becomes dry, continue by adding some polishing paste until the sand scratches have been removed and the lens is
clear.
Polish and Protect
Remove the masking tape and wipe the headlight lens using attached cleaning cloth. Using UV Protective Paste (STEP 3) to polish and prevent UV damage.
The product of instructions in Russian:
Customer feedback:
NOTICE :How to apply UV Protective Paste ?
In a cool shade , using UV Protective Paste to polish headlight surface with white sponge gently toward a direction of smearing until the varnish is evenly coated on the lamp surface. Set it aside for 15 minutes 10-15min (time control is very important ),then the car moved under the sun (exposure above 2 hours)
Precautions:
Avoid eye contact. Do not get on skin or clothing.
Avoid breathing of vapors. Use only with adequate ventilation.
Do not swallow.
Wash thoroughly after handling. Close container after each use.
Storage:
Products shall be ideally stored in a cool ,dry location in unopened containers at a temperature between 8-28 degree c ( 46 to 82F) unless otherwise labeled.
Windshield repair kit:
Description:
Visbella® Windshield Repair Kit is very handy to help you to repair the broken windshield in just 20 minutes. This kit will minimize the appearance and stop the spread of chips and cracks in your windshield. It removes air from the break, fills it with durable resin and makes it even stronger than before. For best results, repairs should be made as soon as possible after the damage occurs and before the break is contaminated by dirt or water.
Application:
The kit that meets every windshield technicians needs to be able to really repair all star breaks, bullseye breaks, combination breaks,
chips, cracks, etc. Minimizes the appearance, and stops the spread of chips and cracks.
Advantage & Features:
1.Easy to use for all types of lamented windshields
2. Minimizes the appearance of chips and cracks in your Windshield
3.No heating is required
4.Durable resin formula
5.Good for multiple repairs
6.Single ingredient – eliminates mixing
How to use it?
1. Clean out any loose glass particles of the break using push pin. Replace push pin after use. Clean area surrounding break using a dry cloth.
2. Peel backing off one side of adhesive seal, line up hole in seal with center of the break. Firmly press the adhesive seal onto the glass.
3. Peel backing from top side of adhesive seal and put black o-ring in the middle of the adhesive seal. Line up pedestal with adhesive seals making sure tabs match up. Press pedestal to adhesive seal. Run fingers around pedestal to ensure a tight bond.
4. Cut the tip off resin container and empty about three-fourths of the resin being poured. Wipe off any excess resin from tip with cloth and save the empty tube for step 8.
5. Ensure plunger tip is positioned in injector barrel just above the pin valve. Press fit injector into pedestal with the pin valve lined up with the tab. Ensure connection is tight. Pull plunger upward and lock it by engaging lower notch in plunger with spring clip. Let sit for 10minutes .
6. Remove pin valve momentarily to let air in pedestal then replace pin valve. Hold injector with one hand and rotate plunger releasing spring clip from lower notch. Depress plunger downward engage upper notch with spring clip. Let sit for 10-15 minutes.
Notes:Insure the plunger in the right starting position while pressure, otherwise the liquid resin inside pedestal may leak from adhesive seal due to big pressure!
7. Remove the injector and outer edges of pedestal with a safety razor. Once top part of pedestal and seal is bent away from glass surface, grip pedestal tab as shown. Slowly pull up until removed. Wipe and remove excess resin.
8. Slowly squeeze resin container applying several drops of resin into the center of the break area, quickly place a clear curing film over the repair area. Run safety razor lightly over clear film to vent out air bubbles. If possible better to tape the clear film to avoid it side or being blown away.
Working principle:
1. Make the glue inside but not too much or also will be stop the pump.
2. Press the pump make the glue bottom to avoid stop 3 the glue into pump.
3. Make air out by pump then glue dip into crack surface.
4. Make the pump press and let glue inside into crack.
NOTE:
A.Avoid using in direct sunlight – work in a shaded area.
B. Do not work on a hot windshield Park vehicle in shaded area and open windows to cool glass surface.
C. A safety razor is required to remove components and finish repair.
Attion:Avoid any contact with eye, skin, and body of the vehicle.
Keep out of reach of children.
Customer feedback:
Pay attention:
Avoid eye contact. Do not get on skin or clothing.
Avoid breathing of vapors. Use only with adequate ventilation.
Avoid breathing of vapors. Use only with adequate ventilation. Wash thoroughly after handling. Close container after each use.
Products shall be ideally stored in a cool, dry location in unopened containers at a temperaturebetween 8 and 28 Degree (46 and 82 Fahrenheit) unless otherwise labeled. Optimal storage is at he lower half of this temperature range.
To prevent contamination of unused product, do not return any material to its original container
Description:
Visbella® Windshield Repair Kit is very handy to help you to repair the broken windshield in just 20 minutes. This kit will minimize the appearance and stop the spread of chips and cracks in your windshield. It removes air from the break, fills it with durable resin and makes it even stronger than before. For best results, repairs should be made as soon as possible after the damage occurs and before the break is contaminated by dirt or water.
Application:
The kit that meets every windshield technicians needs to be able to really repair all star breaks, bullseye breaks, combination breaks,
chips, cracks, etc. Minimizes the appearance, and stops the spread of chips and cracks.
Advantage & Features:
1.Easy to use for all types of lamented windshields
2. Minimizes the appearance of chips and cracks in your Windshield
3.No heating is required
4.Durable resin formula
5.Good for multiple repairs
6.Single ingredient – eliminates mixing
How to use it?
1. Clean out any loose glass particles of the break using push pin. Replace push pin after use. Clean area surrounding break using a dry cloth.
2. Peel backing off one side of adhesive seal, line up hole in seal with center of the break. Firmly press the adhesive seal onto the glass.
3. Peel backing from top side of adhesive seal and put black o-ring in the middle of the adhesive seal. Line up pedestal with adhesive seals making sure tabs match up. Press pedestal to adhesive seal. Run fingers around pedestal to ensure a tight bond.
4. Cut the tip off resin container and empty about three-fourths of the resin being poured. Wipe off any excess resin from tip with cloth and save the empty tube for step 8.
5. Ensure plunger tip is positioned in injector barrel just above the pin valve. Press fit injector into pedestal with the pin valve lined up with the tab. Ensure connection is tight. Pull plunger upward and lock it by engaging lower notch in plunger with spring clip. Let sit for 10minutes .
6. Remove pin valve momentarily to let air in pedestal then replace pin valve. Hold injector with one hand and rotate plunger releasing spring clip from lower notch. Depress plunger downward engage upper notch with spring clip. Let sit for 10-15 minutes.
Notes:Insure the plunger in the right starting position while pressure, otherwise the liquid resin inside pedestal may leak from adhesive seal due to big pressure!
7. Remove the injector and outer edges of pedestal with a safety razor. Once top part of pedestal and seal is bent away from glass surface, grip pedestal tab as shown. Slowly pull up until removed. Wipe and remove excess resin.
8. Slowly squeeze resin container applying several drops of resin into the center of the break area, quickly place a clear curing film over the repair area. Run safety razor lightly over clear film to vent out air bubbles. If possible better to tape the clear film to avoid it side or being blown away.
Working principle:
1. Make the glue inside but not too much or also will be stop the pump.
2. Press the pump make the glue bottom to avoid stop 3 the glue into pump.
3. Make air out by pump then glue dip into crack surface.
4. Make the pump press and let glue inside into crack.
NOTE:
A.Avoid using in direct sunlight – work in a shaded area.
B. Do not work on a hot windshield Park vehicle in shaded area and open windows to cool glass surface.
C. A safety razor is required to remove components and finish repair.
Attion:Avoid any contact with eye, skin, and body of the vehicle.
Keep out of reach of children.
N***s –
Looks like a good quality product, good price and fast shipping. Just need to try /test…
K***v –
отправили 07.06,получил 24.06,в Приморье. Брал за 1.205 р.Запаковано в картоную коробку,пришла изрядно помятой,всё цело.Внутри фирменные пластиковые упаковки,на вид всё отлично.Попробую в деле,напишу
A***t –
ok 🙂
Customer –
Thank you very much for your utmost efficiency. Very good product.
D***n –
Очень быстро. без повреждений
S***c –
Ok
L***. –
Fast delivery! Ordered 11.11.2019 – Received 25.11.2019. Package arrived within 14 days from ordering time. Delivery is trackable. I haven’t tried this set yet. So if after using it I will see that something is wrong – I will leave additional feedback. For now I recommend this store because of fast shipping.
G***y –
produit pour phare très bien, et pour le pare brise pas encore utilisé
S***s –
Товар соответсвует описанию, пришёл быстро